INHOUDSOPGAWE:
- Stap 1: Passaggio 1: Fare Delle Bozze
- Stap 2: Passaggio 2: Iniziare a Montare
- Stap 3: Passaggio 3: La Progettazzione Vera E Propria
- Stap 4: Passaggio Finale
![Braccio Robotico: 4 stappe Braccio Robotico: 4 stappe](https://i.howwhatproduce.com/images/002/image-3125-13-j.webp)
Video: Braccio Robotico: 4 stappe
![Video: Braccio Robotico: 4 stappe Video: Braccio Robotico: 4 stappe](https://i.ytimg.com/vi/Q9JOKQaIR1w/hqdefault.jpg)
2024 Outeur: John Day | [email protected]. Laas verander: 2024-01-30 07:23
![Braccio Robotico Braccio Robotico](https://i.howwhatproduce.com/images/002/image-3125-14-j.webp)
Tinkercad -projekte »
in questo progetto vi mostrero come creare un braccio meccanico con arduino in pochi passi
Stap 1: Passaggio 1: Fare Delle Bozze
![Passaggio 1: Fare Delle Bozze Passaggio 1: Fare Delle Bozze](https://i.howwhatproduce.com/images/002/image-3125-15-j.webp)
![Passaggio 1: Fare Delle Bozze Passaggio 1: Fare Delle Bozze](https://i.howwhatproduce.com/images/002/image-3125-16-j.webp)
prima di iniziare seriamente se volete potete fare delle bozze per vedere se siete in grado di modellare delle figure 3D
Stap 2: Passaggio 2: Iniziare a Montare
![Pas 2: Inisieer na Montare Pas 2: Inisieer na Montare](https://i.howwhatproduce.com/images/002/image-3125-17-j.webp)
![Pas 2: Inisieer na Montare Pas 2: Inisieer na Montare](https://i.howwhatproduce.com/images/002/image-3125-18-j.webp)
dopo il passaggio 1 inisieer 'n montere en pezzi e in teoria dovrebbe venire fuori una cosa del genere
Stap 3: Passaggio 3: La Progettazzione Vera E Propria
![Passaggio 3: La Progettazzione Vera E Propria Passaggio 3: La Progettazzione Vera E Propria](https://i.howwhatproduce.com/images/002/image-3125-19-j.webp)
![Passaggio 3: La Progettazzione Vera E Propria Passaggio 3: La Progettazzione Vera E Propria](https://i.howwhatproduce.com/images/002/image-3125-20-j.webp)
iniziate a fare dei componenti (ricodatevi che è semper meglio fare prima una bozza cartacea) subito dopo vedete se vegono bene e non dimenticatevi le misure dei servomotori che andranno applicati alla fine
Stap 4: Passaggio Finale
![Passaggio Finale Passaggio Finale](https://i.howwhatproduce.com/images/002/image-3125-21-j.webp)
montate i pezzi creati nello scorso passaggio e d ecco il vostro braccio (progetto creato con tinkercad)
Aanbeveel:
Spelontwerp in vyf stappe: 5 stappe
![Spelontwerp in vyf stappe: 5 stappe Spelontwerp in vyf stappe: 5 stappe](https://i.howwhatproduce.com/images/001/image-2360-j.webp)
Spelontwerp in fliek in 5 stappe: Flick is 'n baie eenvoudige manier om 'n speletjie te maak, veral iets soos 'n legkaart, visuele roman of avontuurlike spel
Gesigsopsporing op Raspberry Pi 4B in 3 stappe: 3 stappe
![Gesigsopsporing op Raspberry Pi 4B in 3 stappe: 3 stappe Gesigsopsporing op Raspberry Pi 4B in 3 stappe: 3 stappe](https://i.howwhatproduce.com/images/002/image-5374-j.webp)
Gesigsopsporing op Raspberry Pi 4B in 3 stappe: in hierdie instruksies gaan ons gesigsopsporing uitvoer op Raspberry Pi 4 met Shunya O/S met behulp van die Shunyaface-biblioteek. Shunyaface is 'n biblioteek vir gesigherkenning/opsporing. Die projek het ten doel om die vinnigste opsporing en herkenningssnelheid te bereik met
DIY Vanity Mirror in eenvoudige stappe (met LED -strookligte): 4 stappe
![DIY Vanity Mirror in eenvoudige stappe (met LED -strookligte): 4 stappe DIY Vanity Mirror in eenvoudige stappe (met LED -strookligte): 4 stappe](https://i.howwhatproduce.com/images/002/image-5147-9-j.webp)
DIY Vanity Mirror in eenvoudige stappe (met behulp van LED Strip Lights): In hierdie pos het ek 'n DIY Vanity Mirror gemaak met behulp van die LED strips. Dit is regtig cool, en u moet dit ook probeer
Arduino Halloween Edition - Zombies pop -out skerm (stappe met foto's): 6 stappe
![Arduino Halloween Edition - Zombies pop -out skerm (stappe met foto's): 6 stappe Arduino Halloween Edition - Zombies pop -out skerm (stappe met foto's): 6 stappe](https://i.howwhatproduce.com/images/002/image-5208-7-j.webp)
Arduino Halloween Edition - Zombies pop -out skerm (stappe met foto's): wil u u vriende skrik en 'n skreeu geraas maak tydens Halloween? Of wil u net 'n goeie grap maak? Hierdie pop-up skerm van Zombies kan dit doen! In hierdie instruksies sal ek u leer hoe u maklik Zombies kan spring deur Arduino te gebruik. Die HC-SR0
Brazo Robótico Con Agarre Automático Y Movilidad: 7 stappe
![Brazo Robótico Con Agarre Automático Y Movilidad: 7 stappe Brazo Robótico Con Agarre Automático Y Movilidad: 7 stappe](https://i.howwhatproduce.com/images/002/image-3548-6-j.webp)
Brazo Robótico Con Agarre Automático Y Movilidad: Los robots en niveaus vir die produksie en vervaardiging ha inkrementado